How To Monitor Network Traffic On Router 2021

You are currently viewing How To Monitor Network Traffic On Router 2021

Topic: How To Monitor Network Traffic On Router


Learning how to monitor network traffic on a router? The internet is a great resource when it comes to quick information. However, there are certain things that can slow down your internet connection or can cause other problems as well. Many people have been wondering how to monitor network traffic on a router? Here is how you do it.


First of all, you will need to make sure that your router has all of the necessary hardware needed for it to accept both cable connections and DSL. If it does not have this hardware, you may have some added hardware to add to it to allow for both of these forms of connection.

Once you have this hardware in place, then you can start your search for information on how to monitor network traffic on a router. A quick search on the internet should point you in the direction of the software that is available. This software is used for controlling the traffic between your computer and the internet as well as for controlling the flow of data that goes through your router.


Once you have the right software, the next step in learning how to monitor network traffic on a router is to find the name of the software. Once you have this name, you will be able to easily find it and install it on your router.

With this software, you will be able to see all of the traffic going through your computer from your router, which will give you insight into what your internet service provider or whoever else may be sending you traffic is doing. You can then block this traffic or limit it in other ways.


How To Monitor Network Traffic On Router

  1. Router’s IP address is required. Generally most it’s 192.168.1.1, unless someone changed it. To be sure, open a command prompt, and run ipconfig. For Mac and Linux, run ip r. For Windows, the router’s IP is listed as the Gateway. On Linux, it’ll be default via.
  2. Next in your web browser enter the router’s IP address in the address bar. And press enter exactly like browsing to a website.
  3. You’ll be required to enter your router’s admin username and password.
  4. After your first sign in, you’ll reach a basic status page. Put effort into finding a Device List link to look connected devices to the network.
  5. The router’s device list will open the IP addresses of the devices connected to the network. They can also provide information about what they are. Generally the computer’s name is available next to the IP, if it was set. You will find connection information for Wi-Fi devices, with their signal quality and the available bandwidth.
  6. Look for a Status section on your router. Your luck may give you a specific Bandwidth or Network Monitoring section. 
  7. After locating your router’s traffic or bandwidth monitoring sections, now you can see which devices are using the most bandwidth. See transmission rates and other useful stats. Also, you may find graphs and even real-time monitoring. 
  8. With available information, you’ll find out what your networks biggest hogs are and what devices have problems to get a decent signal. You’ll also be able to see any suspicious activity onto your network.

Also Read: TP-Link AC1750 Smart WiFi Router Review

How To Monitor Network Traffic On TP Link Router

how to monitor network traffic on tp link router

Follow the steps below. For that we take Archer MR200 as demonstration.

1. Please log into the web-based management interface of TP-Link Router

2. Head towards Advanced > Network > Data Settings page. Enable Data Limit and usage alert to prevent data over use.

3. Put the amount allowed for total/monthly data in the data limit Allowance field. When data usage breaks the allowed level, the router will disconnect and a notification will be sent to you on the Basic > Network Map Page.

4. Enter a limit in the Usage Alert field to prohibit data over use. 

5. Activate Data Statistics to configure data statistics when the next billing cycle starts.

6. Put the first date of the billing cycle in the Start Date field.

7. Save the settings.


Also Read: Netgear AC1900 WiFi Range Extender Review

How To Monitor Network Traffic On Router Netgear?

Using The Web Interface:

  • Power up Netgear router and connect a computer.
  • After that launch a web browser on the system, put Netgear router’s login URL and press Enter.
  • After the router login page opens up, type the username and password required to log in the router’s configuration page.
  • Router’s configuration page will open. Press the Advanced tab.
  • Choose the Traffic Meter option, and then enable Traffic Meter.
  • To control the Internet traffic of the router, press the radio button of the Traffic Volume Control menu.
  • Choose one of the control options – No Limit, Download only, and Both Directions.
  • If you want to control the network or connection time, choose Connection time control and put a number of hours that you want to allow connection beside the Monthly limit field.
  • In the Traffic counter, if you want the counter to start now, then select the Restart Counter Now button.
  • Enable Traffic Control indicator light to glow in case traffic limit exceeds.
  • Refresh to check the Traffic Status to view the network traffic volume.

How To Monitor Network Traffic On Router

In The Netgear Genie App:

  • Install the Netgear Genie app in the mobile after connecting to the router’s WiFi, and now open it.
  • Click the Traffic Meter icon on the main screen and turn it on.
  • Configure the monthly traffic limit, counter start day & time, and the traffic volume limit.
  • After settings completion, click the Save button situated at the upper right corner and finally you know how to monitor network traffic on router. 

Leave a Reply